Get $10 bonus once register ! Register NowX

2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino

$20.70

Have chosen: There are no options selected.

Start To Order

Added To Cart Successfully!

2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino
2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino
2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino
2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino
2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino
2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino

2pcs/sets LORA SX1278 ESP32 0.96 OLED 16 Mt Bytes (128 Mt bit) 433Mhz for Arduino

     
  • Product CodeChip
Choose your quantity
11
PLEASE DRAG OR INPUT

Quantity

Enter the quantity you'd like, or click and drag our orange 'o' to find a quantity and price that's best for you.

Price EACH

$20.70

TotalUS$ 20.70

You save$-20.70

If you have your own design, please contact us, there will have a professional customer service to communicate with you.

Don't have your files right now?No worries, Check out our art tips for more information.

If over 500pcs, mass production will start until pre-production sample has been approved.

Est. 7 days production

Describe:

The 433MHz antenna must be used in conjunction with the IPEX interface (if the antenna is not connected, it may damage the LoRa chip)

Lithium battery charging and discharging circuit, when the battery is full, the blue LED will stop working. When using, pay attention to the positive and negative of the battery, otherwise it will be damaged!

Using the IO port touch screen touch signal input, you need to add the 100nF pull-down capacitor at this pin!

Example:

This product is a SX1278 chip based on ESP32 WIFI increased OLED, namely LoRa remote modem, 433MHz frequency, high sensitivity is about -148dBm, +20dBm output power, high reliability, long transmission distance.

The onboard 32MByte Flash, Wi-Fi antenna, 0.96 inch blue OLED display, lithium battery charging circuit, CP2102 interface and USB serial chip, the perfect support for Arduino development environment, can be used for program verification and product development is very simple and fast.

Operating voltage: 3.3V to 7V

Operating temperature range: -40 degrees C to +90 degrees C

Support for Sniffer, Station, softAP, and Wi-Fi Direct modes

Data rates: 150 [email protected] HT40, 72 [email protected] HT20, 54 [email protected], 11 [email protected]

Transmit power: 19.5 [email protected], 16.5 [email protected], 15.5 [email protected]

Receiver sensitivity up to -98 dBm

UDP sustained throughput of 135 Mbps

Note:This product does not include the battery.

 

Shipping list:

ESP32 OLED×2

Line×2

pin×4

433m Spring Antenna×2

Write a review

Write a review

Note: HTML is not translated!
   Bad      Good

{{up_most_image}}

No need register, just fill in contact info below, we will reply you within 24 hours!

Enter the code in the box below: